-
FARO Laser Tracker Accuracy: 7 Mistakes I Learned the Hard Way
-
1. How accurate is a FARO laser tracker really?
-
2. What’s the biggest mistake people make with laser trackers?
-
3. Is FARO laser tracker worth the investment compared to a traditional CMM?
-
4. How often should I calibrate my FARO laser tracker?
-
5. Can I use a FARO laser tracker for everything?
-
6. What about 1507 insulation resistance testers and thermocouple adapters?
-
7. Is Balluff a good brand for sensors?
-
8. What’s one thing you wish you knew before buying a laser tracker?
-
1. How accurate is a FARO laser tracker really?
FARO Laser Tracker Accuracy: 7 Mistakes I Learned the Hard Way
I’ve been handling measurement equipment orders for 8 years. I’ve personally made (and documented) 5 significant mistakes, totaling roughly $18,000 in wasted budget. Now I maintain our team’s checklist to prevent others from repeating my errors. This article answers the questions I wish I’d asked earlier—about FARO laser tracker accuracy, calibration, and when to use other tools. Here’s what we’ll cover:
- How accurate is a FARO laser tracker really?
- What’s the biggest mistake people make with laser trackers?
- Is FARO laser tracker worth the investment compared to a traditional CMM?
- How often should I calibrate my FARO laser tracker?
- Can I use a FARO laser tracker for everything?
- What about 1507 insulation resistance testers and thermocouple adapters?
- Is Balluff a good brand for sensors?
- What’s one thing you wish you knew before buying a laser tracker?
1. How accurate is a FARO laser tracker really?
Accuracy is conditional. Not absolute. Per FARO’s official specs (accessed January 2025), the typical accuracy for the Vantage series is ±0.015 mm + 6 µm/m. But that’s under ideal conditions. In my first year (2017), I made the classic mistake of trusting the datasheet without accounting for environmental factors. We were measuring a large weldment in a shop with fluctuating temperatures. The tracker said everything was within tolerance. It wasn’t. We ended up reworking a $3,200 order. That’s when I learned: the accuracy spec is a starting point, not a guarantee. You need to factor in temperature, vibration, and target quality. Bottom line: a laser tracker is only as accurate as its setup and calibration.
2. What’s the biggest mistake people make with laser trackers?
Skipping calibration checks. I’ve done it. In September 2022, we saved $300 by delaying a routine calibration service. Two weeks later, we scrapped a $4,000 batch because the tracker had drifted. The parts looked fine on the screen. They weren’t. That’s when I created our pre-check list. Now we verify the calibration certificate and run a quick field check before every critical job. Trust me on this one: the cost of calibration is nothing compared to the cost of a bad measurement. The question everyone asks is ‘how accurate is it?’ The question they should ask is ‘when was it last calibrated?’
3. Is FARO laser tracker worth the investment compared to a traditional CMM?
It depends on what you’re measuring. For large parts—think airplane wings, ship components, or heavy machinery—a portable laser tracker is a game-changer. You bring the measurement tool to the part, not the other way around. That cuts downtime and shipping costs. Most buyers focus on the sticker price and completely miss the cost of training and calibration. A traditional CMM still wins for small, high-precision parts where you need sub-micron accuracy. But for large-volume work, the efficiency gain is real. At least, that’s been my experience with large assemblies. We cut our inspection turnaround from 5 days to 2 days after switching to a FARO tracker for our big jobs. That said, don’t ditch your CMM entirely—they complement each other.
4. How often should I calibrate my FARO laser tracker?
Per ISO 10360-10:2016 and FARO’s recommendations (as of January 2025), annual calibration is standard. But if you’re in a high-vibration environment or use the tracker daily, consider every 6 months. We’ve been doing it every 12 months—maybe 10 months, I’d have to check our logs. The key is to track your usage and environmental conditions. A red flag: if you notice measurement drift between checks, don’t wait for the annual service. I learned that the hard way when a drifted tracker caused a 3-day production delay. Put another way: calibration isn’t a cost, it’s insurance against scrap and rework.
5. Can I use a FARO laser tracker for everything?
No. It’s tempting to think one tool does it all. But you need a mix. Laser trackers struggle with small features, deep holes, and shiny surfaces that scatter the beam. For those, a portable CMM arm or a traditional CMM is better. We also use 1507 insulation resistance testers for electrical checks and thermocouple adapters for temperature profiling. Different tools for different jobs. The ‘one tool fits all’ advice ignores the nuance of measurement uncertainty. If you’re measuring a 10-meter assembly, use a tracker. If you’re measuring a 10-centimeter connector, use a caliper or a vision system. Simple.
6. What about 1507 insulation resistance testers and thermocouple adapters?
Those are different beasts, but the same pitfall applies: calibration and verification. We use a 1507 insulation resistance tester for motor checks. One time, we saved $80 by skipping the annual calibration. Ended up with a false pass on a critical motor, which cost us $1,200 in field rework. Same with thermocouple adapters—if the adapter has a cold-junction error, your temperature readings are garbage. The lesson: any measurement tool, whether it’s a laser tracker, an insulation tester, or a thermocouple adapter, needs a calibration schedule. Don’t treat them as plug-and-play. Trust me, I’ve been on the wrong side of that mistake.
7. Is Balluff a good brand for sensors?
We haven’t used Balluff sensors extensively, so I can’t give a definitive yes or no. But here’s how to evaluate any sensor brand: look for calibration certificates, response time, and technical support. Three things: accuracy, reliability, support. In that order. The question everyone asks is ‘who’s cheapest?’ The question they should ask is ‘who answers the phone at 2 AM when a sensor fails on the line?’ For what it’s worth, we’ve had good luck with brands that provide detailed drift specs and a clear calibration interval. If Balluff does that, they’re probably fine. But don’t take my word for it—ask for a sample and test it in your environment.
8. What’s one thing you wish you knew before buying a laser tracker?
Training. Don’t skimp on it. We bought our first FARO tracker in 2017 and thought we could figure it out with the manual. We wasted a month of setup time and made three costly measurement errors. That’s $2,800 in redo plus a week of delay. Now we budget for formal training and a follow-up refresher every two years. The tracker itself is reliable—that said, we’ve only tested it on larger parts, so I can’t speak to every use case. The initial price is just the beginning. Put another way: the cheapest tracker might cost you more in the long run if you don’t invest in training, calibration, and support. A lesson learned the hard way.
Leave a Reply